1.    Capacity of destruction in weight: 60 Kg/h.
2.    It should be able to operate not less than 10 hours/day
3.    This incinerator must be able to destruct all combustible wastes produced by hospitals, private clinics, laboratories, institutes, etc…
4.    Design Specification : Types A, B, C, D, and E of medical waste
5.    “PYROLYTIC” combustion, by controlling the gasification of waste.
6.    The incinerator must avoid the release of black smoke and fine dust, during the loadings.
7.    It should be able to reduce the volume of wastes by 98%.
8.    It should be able to hold emission in the second burn with gas residence of not less than 2 seconds.
9.    The incineration should be completely free from visible smoke as well as offensive odours.
10.    The lower calorific power (L.C.P) of this waste will be 3,500 kcal/kg
?    The Temperatures of combustion: Minimum will be 850oC and max 1400oC
?    Post combustion: >1100oC.
11.    The Internal diameter of the Chimney: ? 400 and its height: 8 m
12.    The Volume of the combustion chamber: 1.200 L
13.    The Dimension of the door for loading in cm: 70×70.
14.    Burner operation should be Automatic On/Off
15.    Fuel : diesel
16.    The supplier must provide  necessary information for the best of  the installation
This incinerator with “PYROLYTIC” combustion must have:
17.    A combustion chamber of waste:
* Perfectly tight door for the manual loading of waste. The loading should be Manual, Batch Load
* A burner of lighting which the use is limited to the ignition of waste.
* Frontage of loading with door seals gone up on hinges, wheel of screw plug, flexible joint, and stuffing insulating out of refractory.

Height: 82″ (208 cm) without pile, 100″ (254cm) with pile

Width:  39.5″ (99 cm) burn chamber, 58″(147cm) at foundation

Length: 62″ (157 cm) overall, 34″(86 cm) at foundation

Weight: 1800 ibs (approximately 816 kg)

Primary Chamber Volume: 10.5 cu.ft. (.28 cu/m)

Suggested Load Volume: 8 cu ft. (22 cu/m) load

Diameter of Stack: 12″ OD (30 cm)

Fuel: Diesel hospital waste incinerator

Fuel Consumption: 3-5gallons/hour (11-18 litre/hour)

Location: Level surface 7 ft (2 meters) from closest construction.

Waste Kind: health care waste

Throughput: 50kg/hr at a nominal calorific value of 4,000kca/kg along with an average bulk density of 120kg/m3 for overall waste and 160kg/m3 for healthcare waste.
Coaching: the Agent will conduct a 2 days incinerators training following installation and commissioning of the equipment.

The Agent shall conduct a 2 days operation & maintenance training into the Biomedical engineering personnel following installation & commissioning of the equipment.

It is carried from the ground level on a considerable steel support frame.  Internally the shell is lined with calcium silicate insulation and a hot face mixture of super obligation brickwork or higher strength castable.

the principal combustion chamber must ensure minimal exit temp is not significantly less than 850? C.
Waste density: 125 into 350Kg/M3
Main Combustion chamber:
Flue gas treatment:  should have particulate remover (scrubbers)
Limiting continuous service limitation 1500? C
Chamber: should really be refractory lined into the following standard;
Chimney/Stack: If be made from refractory lined mild steel or higher quality air-cooled s/s.
Medical waste incinerator for sale Operation manual: 2 sets
Burner: arranged for on/off operation
Fully packaged oil kind, complete with electric ignition and flame failure controls, wired with continuous running enthusiast and finish with valves, fan and motor.
Secondary room: 2 [email protected]? C
Average consumption: at least 4.5Ltrs/hr
1 off diesel-fired ignition burner — temperature controlled

Nanjing Clover Medical Technology Co., Ltd.  Tel: +86-25-8461 0201  Fax: +86-25-8461 0406  Add: RM.

Product Description

Nanjing Clover Medical Technology Co., Ltd..

TS version PLC incinerator is newest design for waste treatment, include health care waste, animal cremation and other solid waste. This gear quality structural for types of site, such as hospital, environmental department, animal cremation services, etc… CLOVER Incinerator supply medical waste incinerator vendor, medical waste incinerator sellor in china, medical waste incinerator small scale, updated models with double combustion space and smoke filter room with refractory lines, and the combustion room temperature up to 1200 deg C.