Nanjing Clover Medical Technology Co., Ltd..

In a simple design with a metal steel drum electric. including:
A cage for receipt of biomedical waste;
A combustion chamber with fireplace with a filter to retain ashes;
A cover;
An air supply;
A turbine  allowing the supply of the air.
Combustion temperature: 1800 ° C. Compliance with European standards.
Comes with all necessary accessories
Supply of incinerator model PDR-18 with:

·        Capacity 100 kg/hr of waste containing up to 85% moisture

?      Two combustion chambers

·        Two fully automatic, oil fired, pressure jet burners

·        Panel board

·         Diesel tank of capacity 250 It. with 2 diesel pipelines, filter and valve.
Type: for animals waste
Capacity: 30 kg per hours for a maximum load of 120 kg.
GLP Gas
Voltage: 110V-120V
Semiautomatic control board
Stainless steel chimney, 3.5 meters above the incinerator.
High temperature painting for all the incinerator.
Front door for loading and unloading.
Fuel    Diesel Oil 8/ kerosene
Capacity (m3)    0.57
Ave Capacity    50 kg per hour
Ave time for Burnout     5 hrs
External Dimensions
Length    2000mm
Width    1100mm
Height including flue    3500mm
Door opening
Internal Dimensions
(primary chamber)
Length    1200mm
Width    620mm
Height     660mm
Operation
Min. operating temperature    9500C
Max. operating temperature    13200C
Residency time in second chamber    2.0 seconds
Weight    1850kgs
Ancillaries
Operating and maintenance manuals
Recommended Spare list
300 liter fuel tank
Plant burning rate – 100kg/hr

Fuel – Diesel oil   – 35 sec Redwood

Overall dimensions are as follows:

Width    2261mm

Length  3264mm

Chimney Diameter  –  390mm

Chimney Height      –  8000mm
chinese incinerator manufacturers, We process 8-10 ton waste of sheep carcass and its byproduct per day. We are looking for the equipment: combustion burners(combined fuel supply:natural gas and diesel),control panel and filter system. The diameter of the incinerator is 20 cm. Lower calorific power of the waste is 4KW/KG. Heating power 4000KW

Solid waste to be incinerated

Cartons,  rags,  cotton  and  other  wastes  associated  with  generation  of  electricity loaded in the incinerator in

bags.

Loading capacity: At least 100 Kg / h

Start up fuel

Diesel Oil

2.3  Incinerator Supply

The incinerator shall be equipped with sludge pumps that allow homogenous flow of sludge to its burner. These pumps

shall deliver waste oil from the incinerator sludge mixing tank to the incinerator. Operation and control of these

pumps shall be fully automatic. A linear negative feedback control algorithm shall be used to adjust the feed rate of

the sludge pumps and hence vary the quantity of sludge being incinerated. The sludge line shall also be equipped with

appropriate self cleaning filter that will keep impurities away from the burner.

A  sludge  mixing  tank  equipped  with  a  superheated  water  heater  shall  also  be

provided. A Superheated water heater shall be provided to heat the waste oil to the inlet temperature required by the

incinerator. In case a superheated water heater

cannot be provided, an electric heater shall be provided for the tank. The tank shall also be equipped with a magnetic

level indicator, level switches and appropriate drain valves, separate overflow and vent pipes.

Characteristics of superheated water available at the power station are as follows; Pressure and temperature of

superheated water at supply manifold; P = 10 Bars, T = 150 Deg

Pressure and temperature of superheated water at return manifold; P = 8.5 Bars, T = 140 Deg

Fully automatic sequential control provided by internal

PLC system providing control of:

1. Secondary chamber pre-heat
2. Burn cycle (variable)
3. Cool down cycle

Fuel Options

Diesel, LPG, Natural or Bio Gas.

Typical Fuel Consumption

Diesel: 8 / 10 litres per hour

Liquid Propane Gas: 6 / 8 litres per hour

Natural Gas: 7 / 9 Nm3 per hour

Electrical supply

240volt 16 amp.

Key Specifications

Chamber Volume 2.38m3:

2.2m (l) x 0.9m(w) x 1.2m(h)

Load Capacity up to 1000kg

Load Method Top

Medical Waste Incinerator will be quoted in accordance with Technical Specifications provided below:

1) A self-contained, diesel fuel, medical waste incinerator with a minimum burn rate capacity of 100 kg/day.

2) A medical waste incinerator shall be specifically designed by the manufacturer to dispose of all Bio-Hazard medical

wastes.

3) At a minimum the unit shall be sized to incinerate 2.0 kg/exam-room/24-hrs when being operated continuously for 12

hours per day, but no less than 100kg/day total.

4) The Incinerator shall be manually batch fed.

We have a 70 bed medical facility in namibia. There’s a potential of getting customers from various other regional physicians.
Please see attached) for a few empty compound bags. Could you please supply me with a few details info about these type of incinerators (small range). a pet incinerator for the cremation of pets and pet cats. It is going to surely be solitary use of each animal seperately.Initially we are planning to start this Pilot Task with the National Medical centre, to convince the Ministry Officials in addition to on its success to carry this project to the Teaching Hospitals, Area and Base Hospitals in the Country.municipality demand 4 crematory machine for bodies. I require some advice regarding price, kine of power for activation, harmful exhaust, The incinerator we are looking must be with the benefits of warm recycling system, usage of hot water, etc. Ability – 150-200 kgs/hr and with International standards.get additional information about the Family pet Cremation Tools, specifically for canines in addition to felines.

We complete this job in year 2010 to 2011 and shipping on Hochiminh port, Vietnam with 1×40’feet open upper complete container.

Big size combustion chamber up to 4.0m3 and Inner Dimensions is 257 x 147 x 108cm with feeding doorway opening 108 x 128cm. This version can be a small waste incineration factory with little quantity of funds funds. If end-user utilize this for farm to burn animals like cow, horse or camel, no problem!