All particles of the waste should achieve a high level of sterilization and not just “disinfection” due to the

continuous agitations

Description of the Treatment Cycle of the processor

1. i) Loading

* The waste has to be loaded by dropping bagged and or boxed waste into the open loading door on the vessel.

* The loading door should be mounted at an angle on time top side, of the vessel with suitably sized to accommodate the

infectious wastes for which it is intended

* Over-loading or loading too tightly should not be an issue with this process, and hence no need of the special

operator skill.

1. ii) Heat-up and fragmentation

* After loading, the vessel door is to be closed, and the outer jacket of the vessel is to be automatically filled with

high temperature steam, which should act as the main heating medium for heating the waste.

* During this heating cycle, the shall and mixing arms should rotate continuously, causing the waste to be fragmented

and continuously tumbled against the hot vessel walls.

* At this point, the waste is broken up into small fragments, and all material heats up rapidly, being evenly and

thoroughly exposed to the hot inner surfaces. The moisture content of the Waste will turn in to steam, and the vessel

will start to pressurize.

* Initially, no steam will be injected into the waste. If there is not enough moisture in the waste to pressurize

the vessel, a small amount of steam is to be automatically added until the desired pressure is reached.

* At the end of this period, the correct sterilization temperature and pressure should be reached, and the

sterilization period should start.

iii) Sterilization period

* The amount of steam fed to the outer jacket is to be regulated to maintain the desired temperature & pressure of the

inner vessel,

* The mixing arms (grinder) MUST continue to rotate throughout this cycle to ensure even sterilization pressure and

temperature for all wastes.

* The treatment time should be either15 minutes at 132° C OR 30 minutes at 121° C to achieve level 6log10

sterilization.

* The intense subjugation of the waste to high temperature and pressure moisture in a dynamic environment should also

cause the waste to hydrolyze that is a rapid decomposition of organic material.

1. iv) De-pressurization:

* After the treatment time, the steam to the jacket should remain on, and the internal vessel is to be vented through a

condenser, and de-pressurized. Thus, the waste loses its water content through a combination of heat input from the

jacket and flashing of water due to depressurization.

1. v) Dc-hydration

* Further dehydration is to be achieved by maintaining heat input and mixing – almost total dryness should be achieved.

1. vi) Unloading

* Finally, steam to the jacket should shut off, the unloading door is to be opened

* Then the shaft and mixing arms are reversed to act as unloading mechanism and should scoop the waste fragments out of

the unloading door, onto a conveyor belt or directly into a waste container.

* The vessel should now be ready for another treatment cycle, having retained most of its heat for the treatment of the

next batch.

Incinerators used will be limited to daylight hours of operation. This includes shutdown, cleaning and maintenance.

Waste streams shall not be mixed during the incineration process and the ash collection chamber will be cleaned when a

different waste stream is to be incinerated. The Company will provide the contractor with a list of items that can be

incinerated.

All ash will be collected and stored in individual storage bins for each particular waste stream. The bins are to be

provided by the contractor to the same design as the storage bins for the raw waste streams and include a lid design

that prevents contamination from water.

Ash from each waste stream will be sent for laboratory analysis after each initial incineration by the Company and at

intervals decided by the Company thereafter. Contractor will be required to collect ash samples for analysis as

directed by the Company. The Contractor will be responsible for the security of samples taken to prevent contamination

until collection by the Company or designated courier.

Ash will be disposed of at the direction of the Company. It is the responsibility of the Contractor to ensure the ash

is not compromised until final disposal. Company will provide additional storage area for ash if and as required.

Delivery Schedule

The delivery schedule for the unit with capacity 100 kg/h requested is no greater than 10 weeks and 14 weeks for the

unit with capacity 150 kg/h.  These timelines include unit mobilization. Location ,Erbil ,IRAQ.

APPENDIX A

WASTE INCINERATORS RECOMMENDATIONS

1. Multiple chamber type, horizontal stationary cylindrical body;

2. Capacity of 15 kilograms per hour;

3. Diesel-Powered;

4. Burners should  be  monoblock  type  with  built-in  fan,  motor,  electronic  programmer, automatic

ignition, fuel regulator, registration  and security sensor  device for the absence of flame triggering solenoid valve

mounted on the easel supply;

5. The system should have ventilation for sweeping previous gases before activating the fuel supply to the

burner;

We seek a lasting growth consequently we are adopting an enduring medical waste monitoring system, that includes constructing a modern long lasting incinerator that will certainly not just provide for our center yet also for the numerous other centers in the larger place of the location. Waste kind: health care danger waste and standard waste
5. Chimney:
Smokeshaft: 3.5 mm light steel
Altitude from base:11 m and additionally if there are structures within
30m of the heater, smokeshaft needs to extend at least 3m
above the pinnacles of all the roofing of such buildings
Size of smokeshaft at leading:430 mm.
Weight of pile: ± 500 Kg.
Instance and pile be repainted with 400 ⁰ C warmth immune Black paint.
6. Heating systems:.
First chamber 850 ⁰ C—- 900 ⁰ C.
second chamber 1000 ⁰ C.
7. Variable rate burning air blowers.
8. Main chamber amount ± 1.05 cubic metres.
9. Mixing chamber amount ± 0.30 cubic metres.
10. Dealing with chamber quantity ± 0.89 cubic metres.
11. Weight excluding smokeshaft ± 6.400 Kg at manufacture.
12. Shooting tools provided: Hoe, texas hold’em in addition to rake.
13. Dimensions.
Dimension ± 2125mm.
Size ± 1890mm.
Elevation ± 2125mm.
Additional dimension for burners ± 1000mm.
14. Packing door opening 610 * 540mm.
15. Fireplace area ± 1.19 square metres.
16. Summary of grate/hearth: A total hearth to be supplied to prevent contaminated.
17. Fluids from streaming right into ash pit without being blazed.
18. Conformity with South African Atmospheric Contamination Avoidance Act No. 45 of.
1965 or equal air contamination criteria.
19. Documents to be provided: Treatments and likewise maintenance manual along with demand.
running treatments (SOPs).
20. Exhaust controls:.
warmed refractory screen.
Reduced rate grit clearing up chamber.
Stainless-steel arrester display

21. Refractory product: alumina content> > > > 49% as well as density common 102mm.
22. : to be corrected 2-3 days.
23. Products of structures.
Case:5 mm moderate steel.
Sustaining: heavy angle and likewise network.
Hearth: 1550 ⁰ C.
Ashing door: high quality cast iron.
Packing door 5mm modest steel lined with 1550 ⁰ C castable fundamental purpose high strength, high abrasion resistant monolithic refractory concrete.
Burner wall surface surfaces in addition to roof covering: 1550 ⁰ C castable monolithic refractory

Gasified incineration for shedding medical wastes.

Gas kind: Gas
Developed to melt disposables that can as well as should certainly be destroyed on-site. Theses wastes include also contaminated and infectious “red bag.” Surgical dressings, plastic assessment tools as well as different other wastes.
Quick, total, efficient garbage disposal.
Twin chamber combustion, Chambers insulated and also lined with high temperature refractory. Programmable digital temperature controls, temperature level indications and also cost recorder. Modulating control for gas along with air lowers gas consumption.
Minimum installation as well as also launch time.
Aluminized steel coat lined with refractory and firebrick. Screens recorders as well as likewise various other accessory equipment should be available.
Payment system:.
– – Upright price door on crucial chamber.
– – Pneumatically-driven or hydraulic ram charging system.
– – Car folded of the door after billing.
– – Main as well as additional chamber temperature offered and videotaped (optional).
Charging cost:.
– – As long as 100kgs per hour of waste or red bag waste rated at 2200 BTU’s per kg.
Gas:- Gas.
Capacity (Cubic Mtr): 1.65 M3 and even a lot more.
Ave Capability: 100kg per hr.
Added Chamber Capability (CubicMtr):3.88 or even more.
Size (mm): 1880 or much better.
Width (mm): 1280 or better.
Height Incl. Flue (mm): 7700 or much better.
Ash Door Opening (mm): 475×× × × 900 or much better.
Minutes. Running temperature level: 90 level centigrade.
Max, Operating Temperature: 1350 level centigrade.
Residency time in Secondly Chamber: 2 sec.
Temperature Tracking: Both for additional and main chambers.
Filling SystemManual/semi-automatic.
Waste devastation effectiveness: > > 90% by weight.
Filter: Different or ceramic other equivalent filters in order to decrease the induction of unsafe air pollutants, particulates, carbon monoxide gas, dioxin/furane right into the setting.
De ashing system: Manual/semi-automatic.
– Civil features. – Waste collection Trolleys.
Re-burning machine: Power max 0,2 kW Voltage: 220V/ 380V.
Weight: max 5000 kg

Burner size: max 2000x1200x3200 mm
Burning room volume:
–– Gasification space max 0.7 m3,
–– Additional burning area max 0.5 m3 ，

Dimension of the filling up entry: max 650×× 850 mm Air blower: max 0,5 kW Combustion-support burning devices: – Power max 0,2 kW INCINERATOR (WASTE BURNER).
Created to burn disposables that can as well as ought to be ruined on-site. Theses wastes consist of transmittable and also infected “red bag.” Surgical dressings, plastic examination tools as well as various other wastes.
Rapid, total, efficient garbage disposal.
Twin chamber combustion, Chambers insulated and also lined with high temperature refractory. Programmable digital temperature controls, temperature signs and also cost recorder. Modulating control for gas as well as air decreases gas consumption.
Minimum installment and also launch time.
Aluminized steel jacket lined with refractory and firebrick. Screens recorders and also other accessory equipment must be available.
Billing system:.
– Vertical cost door on key chamber.
– Pneumatic or hydraulic ram charging system.
– Auto closed down of the door after billing.
– Main as well as secondary chamber temperature presented and recorded (optional).
Charging price:.
– As much as 100kgs per hour of waste or red bag waste ranked at 2200 BTU’s per kg.
Fuel:- Natural Gas.
Capacity (Cubic Mtr): 1.65 M3 or even more.
Ave Ability: 100kg per hr.
Additional Chamber Capacity (CubicMtr):3.88 or more.
Size (mm): 1880 or far better.
Width (mm): 1280 or better.
Height Incl. Flue (mm): 7700 or far better.
Ash Door Opening (mm): 475×× 900 or much better.
Min. Running temperature level: 90 degree centigrade.
Max, Operating Temperature: 1350 level centigrade.
Residency time in Second Chamber: 2 sec.
Temperature Monitoring: Both for main and secondary chambers.
Filling SystemManual/semi-automatic.
Waste destruction efficiency:> > 90% by weight.
Filter: Ceramic or various other equal filters in order to lower the induction of unsafe air contaminants, particulates, carbon monoxide, dioxin/furane into the environment.
De ashing system: Manual/semi-automatic.
The System needs to be priced estimate total with:-.
– Pipes.
– Electric panels.
– Civil functions.
– Waste collection Trolleys.
Re-burning machine: Power max 0,2 kW Voltage: 220V/ 380V.
Weight: max 5000 kg

Enhanced concrete positioning foundations, nourish or billing receptacles (or loaders), main combustion chambers

with ash cleanout doors, instant burning chambers with ash cleanout doors, cyclone air filters (or separators),

and also forced air exhaust heaps (or chimneys). Heater

and additionally combustion air controls shall be wholly automatic including, as a minimum, digital ignition in addition to all

required interlocks in addition to likewise security and protection tools to provide secure operation. Burner in addition to combustion air controls will be wholly automatic

making up of, as a minimum, digital ignition and also all required interlocks and safety and security and also safety gadgets to offer safe

operation.

The conforming with will be offered as a minimum:

Strengthened concrete positioning constructions, feed or billing hoppers (or loaders), main burning chambers

with ash cleanout doors, added combustion chambers with ash cleanout doors, cyclone air filters (or separators),

and also forced air exhaust stacks (or chimneys). Heater

in addition to also combustion air controls shall be wholly automatic consisting of, as a minimum, digital ignition in addition to all of

required interlocks in addition to also safety tools to provide safe operation. Heater in addition to burning air controls will be completely automated

comprising of, as a minimum, digital ignition in addition to also all required interlocks and safety in addition to protection devices to provide protected

procedure.

2nd burning chamber will be a solid-walled in addition to additionally – pumped down, straight, refractory-lined cyndrical tube type

incinerator created to oxidize (or discard ) the organic vapors in addition to gases. Heating system and draining air controls will likely be

fully automated containing of, as a minimum, digital ignition in addition to all required interlocks and likewise safety in addition to safety and security apparatus to

deal secure operation. The chamber and burner will be made to preserve a minimal combustion temperature of a minimum of

930 to 980 C (1700 to 1800 F), but will not to exceed 1150 C (2100 F). The ash-removal system shall consist of, as

a minimum, the right guidebook removal into a completely dry

Cyclone air filters will be offered to eliminate the larger particulates. Cyclone air separators might be provided with

driven followers to enhance the rate of the gases inside the cyclone to enhance the collection effectiveness for smaller sized

bits.

5.16.2 MEDICAL WASTE INCINERATORS

Medical waste burners will be particularly made by the supplier to eliminate medical wastes. All apparatus shall be made for 8 hrs

per day of continuous procedure in addition to be rated in volume per hr (i.e. kg/hr or lbs/hr).

Burner packaging or billing of medical waste will be batched-fed by hand.

Main burning chamber shall function as static fixed-hearth (or kiln), multiple-chamber, retort type or bigger

ability rotary-hearth (or kiln) kind. Heater in addition to burning air controls will be completely automatic including, as a

minimal, digital ignition and all essential interlocks in addition to safety tools to offer safe procedure. The

chamber in addition to burner will be designed to keep a minimal burning temperature of at the very least 760 to 870 C

(1400 to 1600 F). The ash-removal system shall include the automatic continual elimination of the ash into an ashquench

pit in which cooled by water and eliminated by conveyor.

Second burning chamber will be a solid-walled and also -floored, horizontal, refractory-lined cyndrical tube type

incinerator designed to oxidize (or discard ) the organic vapors in addition to gases. Heater and draining air controls will be

fully automatic containing of, as a minimum, digital ignition in addition to all needed interlocks and also security and protection tools to

offer secure operation. The chamber in addition to burner will be created to preserve a minimum combustion temperature amount

of minimum of 930 to 1200 C (1700 to 2200 F) using a minimum gas house (or live ) time of 2.0 secs. The ashremoval

system shall comprise, as a minimum, the direct manual elimination into a completely dry set receptacle.

Cyclone air filters will be awarded to eliminate the larger particulates. Cyclone air separators might be provided with

driven followers to elevate the rate of the gases inside the cyclone to enhance the collection efficiency for smaller

particles. Stacks shall be the forced-air kind and

completely independent and also unattached to nearby structures. As a minimum, heap peaks will reduce

downwash of stack discharges because of end resistant effects from close-by frameworks and be determined in accordance

using DoD 4715.05-G, Overseas Environmental Standard Assistance File. Heaps shall be provided using

corrosion-resistant steel climate caps. ”

{
(adsbygoogle = window.adsbygoogle || []).push({});|}{
(adsbygoogle = window.adsbygoogle || []).push({});|}
Metropolitan burners using a 10-metric ton/24-hour capacity, finish with Stacks, control board and moreover all accessories, complying with 01015 the same level. 5.16.1.

Medical burner using a 10 kg/hour (15 lbs/hour) capacity will be enhanced the website, total amount with Lots, control panel in addition to all resources, abiding by 01015 the very same level. 5.16.2.
Glass containers in addition to aluminum-.
Fat-. Filter, tires, belts.
Plastic container.

a specific kind to generate use of at a crematorium. Is this thing ideal, are ashes conveniently gathered and also so on a cremator, for pet center, can you present and also all detail of earnings, tax responsibility, environtment.-Plastic.
LARGE Quantity.
– – Chemicals, paint.|

Medical burner using a 10 kg/hour (15 lbs/hour) capacity will be enhanced the website, total amount with Lots, control panel in addition to all resources, abiding by 01015 the very same level. 5.16.2.
– – Chemicals, paint.
Fat-. Filter, tires, belts.
Metropolitan burners using a 10-metric ton/24-hour capacity, finish with Stacks, control board and moreover all accessories, complying with 01015 the same level. 5.16.1.