18   Electrical supply required 3-phase

19   Auxiliary fuel      Diesel or paraffin

20   Primary burner

21 Secondary (after) burner

22 Type of burners   Automatic pressure jet

23   Output Primary   Approx 600 000 kJ/hour

24   Output Secondary      Approx 750 000kJ/hour

25 Emission control

Heated refractory screen

Low velocity grit arrester screen     Built in

26   Paint case     400 degree Celsius resisting black

27   Paint stack    400 degree Celsius resisting aluminium

28 Temperature of case   Not exceeding 90 degree Celsius

29   Intensifier

30   Automatic fan control

31   GRE factor  1.5

32   Noise (primary)

Noise (secondary)      72 dBA

33   Transport and rigging of plant including crane hire    76 dBA

34   Certificate of analysis as per Annexure 1

35   Commissioning of incinerator

36   Guarantee     3 years

37   Training of operators

38   Availability of local distributor for spare sparts

ANNEXURE 1

Common Name   Chemical symbol Compliance: mg/Nm3 under normal conditions of 10% O2, 273 Kelvin and 101.3 kPa

Particulate matter              10

Carbon monoxide      CO 50

Sulphur dioxide  SO2       50

Oxides of nitrogen     NOx expressed as NO2    200

Hydrogen chloride     HCl       10

Hydrogen fluoride     HF  1

Sum of Lead, arsenic, antimony, chromium, cobalt, copper, manganese, nickel, vanadium     Pb+, As+, Sb+, Cr+, Co+, Cu+,

Mn+, Ni+, V       0.5

Mercury Hg  0.05

Cadmium Thallium    Cd+Ti    0.05

Total organic compounds  TOC      10

Ammonia     NH3      10

Compliance: ng I TEQ/Nm3 under normal conditions of 10% O2, 273 Kelvin and 101.3 kPa

Dioxins and furans     PCDD/PCDF      0.1

Nanjing Clover Medical Technology Co., Ltd..

4. Ensure flame contact with all gases is achieved. –yes
5. Ensure residence time is not less than two (2) seconds. –yes
6. Ensure the gas temperature as measured against the inside wall in the secondary chamber & not in the flame

zone, is not less than 1100oC.—1000-1200 oC

7. Ensure the oxygen content of the emitted gases is not less than 11%.–yes
8. Ensure both primary and the combustion temperatures are maintained until all waste has been completely

combusted–yes

5     Particulate Removers A mechanical particulate collector must be incorporated after secondary combustion

chamber for removal of particulate pollutants entrained in the flue gas stream. The particulate collectors may include

any of the following or a combination thereof:

Cyclone separator

Electrostatic precipitators

Fabric filters— filter brick

6     Chimney / Stack  1.    The chimney should have a minimum height of 10 meters above ground level and clear the

highest point of the building by not less than 3 meters for all roofs. The topography and height of adjacent buildings

within 50 meters radius should be taken into account.—6 meter already, can plus 4 meters, free cost

2. If possible the chimney should be visible to the operator from the feeding area.—according to local site
3. The addition of dilution air after combustion in order to achieve the requirement of these guidelines is

unacceptable.

4. The minimum exit velocity should be 10 m/s and at least twice the surrounding wind speed (Efflux velocity =

wind speed x 2) whichever is higher to ensure no down washing of exiting gases. .–yes

5. Point for the measurement of emissions shall be provided. .–yes

7     Instrumentation   Instrument for determining the inside wall temperature and not burner flame temperature must be

provided for both primary and secondary chambers.–yes

2. An audible and visible alarm must be installed to warn the operator when the secondary temperature drops to

below the required temperature.

Capacity       Not less than 500Kg/hr.

Operation     24hr-7days/week continuous operation.

Combustion chamber 2 combustion chamber.

Temp.    First combustion chamber 800-1000 C.

Secandry combustion chamber 1000-1200 C, with the possibility to be upgraded to 1400