medical waste incinerator china, Design, supply and manufacture ex works of one Surefire Manual Load TS50/1 Medical/General waste incinerator as detailed below: –

·         Waste type: Mixed type o,1,2,3,&4 hospital/clinical bio hazard waste

·         Waste density: 125 to 350Kg/M3

·         Waste CV: 4000 KCAL/kg

·         Moisture content: 10-25%

·         Estimated ash residue: 5-10%

·         Nominal capacity: 30Kg/hour batch load

·         Secondary chamber: 0.5 second @ 850oC
·         Compact laboratory style

·         Two combustion chambers

·         Ecologically friendly

·         Up to 50kg of waste / hour

·         To be used for animals

Nanjing Clover Medical Technology Co., Ltd.  Tel: +86-25-84610201  Fax: +86-25-84610406

The temperature is over the minimum and under the maximum required temperature (e.g 1150?C) of the thermal

reactor (partial load).

 

When switching off, only the solenoid valve for the fuel supply closes, the burner fan stays on to cool and protect the

burner head.

 

The reactor burner shall be modulating burner with pre-ventilation working on the principle of an oil pressure atomizer

with return nozzle for diesel oil, consisting of:

 

–      Fan housing with high-powered fan and cover

 

–      Electric motor

 

–      Oil pressure pump with built-in oil pressure controller

 

–      Burner nozzle rod with return nozzle and baffle plate

 

–      Coupled control with servomotor, rate controller, regulating segment and air valves

 

–          Electromagnetic shut-off dampers

–      Burner tube with flame pot, burner connection and insulation flange

 

–      Electrical high voltage ignition with ignition transformer and ignition electrodes

 

In the control panel:

 

–      Oil firing sequence control automation relay.

capacity – 50 Kg

 

Burn rate – 20 Kg/h

 

maximum Temperature – 1000C

 

Operating Energy – Diesel

 

Ignition method –

 

Combustion chambers – 2

 

Insulation – refractory Lining

 

No of burners – 2

 

Loading Method – Front load with safety latch

 

Chimney – Heavy duty stainless steel

 

Control – Burner control

 

Thermostat control

 

Timer control

 

Fan timer control

 

Instrumentation -4 Digit temperature display

 

Ash removal – Separate ash removal door

 

Fuel consumption per Kg –

 

Automatic & simple to operate control pannel –

 

3 mm steel casing & fully insulation

 

Dense  refractory concrete lining rated to 1400 degree to C

 

safety chute for easy loading –

 

SS Flue as standard –

 

Heat recovery option –

 

Easy onsite Installation –

secondary chamber

1000 degree

 

chimney

standard

 

shredder

separately

 

Autoclave or microwaves

separately

 

temperature monitor

attached outside of machine

 

operating

Fuel and electric

During the start and end incineration operations at the waste incineration plant the temperature shall be maintained

at 850 °C, while it shall be 1100 °C when incinerating dangerous waste containing halogenated organic substances with

content of chlorine or its compounds. The temperature shall be maintained at 1000 °C during incineration of medical

waste.

MUNICIPAL SOLID WASTE INCINERATORS

 

Municipal waste incinerator quantities and capacities shall be designed for 24-hour 7-day-a-week continuous operation.

 

Incinerators shall be capable of processing both wet and dry material and operating on either diesel fuel, JP-8 fuel,

 

or waste oil; see Plumbing for fuel storage system requirements. The following shall be provided as a minimum:

 

Reinforced concrete mounting foundations, feed or charging hoppers (or loaders), primary combustion chambers

 

with ash cleanout doors, secondary combustion chambers with ash cleanout doors, cyclone air filters (or separators),

GOODS:  ONE INCINERATORS IN ACCORDANCE WITH THE				SUPPLIER’
REQUIREMENT				S	OWN
				PROPOSED
				SPECIFICA
				TION/
				CONFIRM
				ATION
				SPECS
	Height from base: 11m and if there are buildings within 30m of the
	incinerator, chimney must extend at least 3m above the apexes of all
	the roofs of such buildings
	Diameter of chimney at top: 430mm
	Weight of stack: ± 500kg
	case and stack be painted with 400 °C heat resistant black paint
	Burners
	1st chamber 850 oC -900oC
	2nd chamber 1000oC
	Variable speed combustion air blowers
	Primary chamber volume ±1.05 cubic metres
	Mixing chamber volume ±0.30 cubic meters
	Settling chamber volume ±0.89 cubic meters
	Weight excluding chimney ±6 400kg at manufacture
	Firing tools supplied: Hoe, poker and rake
	Dimensions
	Length ±2 125mm
	Width ±1 890mm
	Height  ±2 125mm
	Extra width for burners	±1 000mm
	Loading door opening 610mm×540mm
	Hearth area ±1.19 square metres
	Description of grate/hearth: A full hearth to be supplied to prevent
	contaminated  liquids  from  flowing  into  ash  pit  without  being
	incinerated
	Compliance with South African Atmospheric Pollution Prevention
	Act No. 45 of 1965 or equivalent air pollution standard
	Documents to be supplied : Operations and maintenance manual and
	standard operating procedures (SOPs)
	Emission controls:
	heated refractory screen
	Low velocity grit settling chamber
	Stainless steel arrester screen
	Refractory material: alumina content ≥49% and thickness average
	102mm
	Bake out: to be done over 2-3 days
	Materials of construction
	Case: 5mm mild steel
	Bracing: heavy angle and channel
	Hearth: 1550 °C
	Ashing door: high grade cast iron
	Loading door 5mm mild steel lined with 1550 °C castable general
	purpose high strength, high abrasion resistant monolithic refractory
	concrete
		36

– – – – – – – – Waste will probably be automatic feeding system directly into the burner.

– – – – – – – – Control plank will absolutely be fitted using a beneficial synoptic view disclosing the operating scenario of the entire

heater as well as also cared for by DCS/PLC system.

– – – – – – – – Heating system will certainly be made as a Packaged method, having electrical web link last as well as pre-wired pipes

in placing.

– – – – – – – – Control plank will absolutely be fitted using a valuable synoptic view disclosing the operating situation of the entire

heating system as well as likewise taken care of by DCS/PLC system.

– – – – – – – – TOC of slag as well as bottom ashes will absolutely be much less 3% of the completely dry weight.

– – – – – – – – Heater will surely be created as a Packaged system, having electric connection pre-wired as well as last pipes

in positioning.

– – – – – – – – Burner will surely have automated de-ashing system with higher instructions.

in position.

– – – – Incinerator will possess automated de-ashing system with upward direction.

– – – – Burner will surely have flue gas therapy system comprehensive [emergency scenario by-pass heap, gas heating system,

two activators as well as additionally particulates filtering method ] as well as assurance of discharges out of burner.

– – – – Training of AKU workers at website.

– – – – website could be assessed as well as likewise take a look at existing ATI maker, capacity 150 kg/hr. In 1 day therapy.

– – – – Existing facilities space is conveniently available in basement, 100′ ′ Size x 30 ′ large x 20 ′ Altitude for 2nd Incinerator.

– – – – Existing smokeshaft dimension is 12 meter, and additionally size is 24″ ″ dia.